Access Control & Cameras
Access Control Components and Wiring Explained
The parts of an access control system and how they connect: readers, controllers, locks, request-to-exit, door contacts and power.
Updated November 17, 2026 · 3 min read · Arrowhead Lock & Safe
The building blocks
Every access control door follows the same basic pattern. A reader or keypad collects the credential. A controller decides whether to allow it. A lock or electric release opens the door. A request-to-exit device tells the system someone is leaving so it doesn't raise an alarm. A door position switch reports whether the door is actually closed. A power supply runs the locks and readers.
Readers and controllers
Readers are mounted next to the door and wired back to a controller, usually in a nearby closet or above a ceiling. One controller can handle several doors. The controller connects to the software that stores users and schedules, either on a local computer or through the internet to a cloud service.
Locks and releases
Electric strikes replace the strike in the frame and let the latch pass when powered or unpowered, depending on the setting. Maglocks hold the door shut with a magnet and release when power is cut. Electrified levers and exit devices put the electric control inside the lock itself. Each choice has trade-offs for security, life safety and the type of door.
Exit, monitoring and power
Request-to-exit sensors or buttons, along with mechanical exit hardware, make sure people can always leave. Door position switches let the system report doors held or forced open. Power supplies with battery backup keep systems running briefly during outages, and the fail-safe or fail-secure setting decides what each door does when power is lost.
Network and software
Modern controllers connect to the building network so the software can push user changes and collect logs. That connection should be on a secured network, with strong administrator passwords and updates applied regularly. Cloud-managed systems handle updates for you and allow remote management, while on-site systems keep everything inside the building.
Common installation problems
Many access control problems come from small installation details: a strike that doesn't match the latch, a maglock without a proper release for exit, a door position switch mounted where it reads incorrectly, or power supplies without battery backup. Long wire runs without the right gauge can cause locks to chatter or fail to release.
Each of these shows up as a door that doesn't behave, and each is avoided with careful planning and testing door by door.
Testing every door
After installation, every door should be tested for the full set of conditions: unlocks for an authorized card, stays locked for an unauthorized one, relocks after it closes, reports when it's propped open, lets people out freely, and behaves correctly during a power loss. Ask your installer for that checklist before signing off on the job.
Wireless and standalone options
Not every door needs a wired reader. Wireless locks communicate with a nearby gateway and run on batteries, which is useful on interior doors, glass walls or historic buildings where running cable is impractical. Standalone keypads store codes in the lock itself and don't connect to a central system, making them a simple choice for one or two doors. The trade-off is management: battery changes, and with standalone locks, programming each door individually.
Why professional installation matters
Getting the parts right matters less than getting them right for each door: the correct strike for the latch, the right release mode for code, clean wiring, and a door that closes properly. Mistakes show up as doors that won't lock, won't release or trigger constant alarms.
Arrowhead installs and services access control hardware across metro Atlanta. Call 404-351-4331.
Frequently asked questions
What's the difference between fail-safe and fail-secure?
Fail-safe hardware unlocks when power is lost; fail-secure stays locked. The right choice depends on the door and life-safety requirements.
Can I install access control myself?
Simple standalone keypads can be DIY, but networked systems involve door hardware, wiring, power and code requirements best handled by a professional.
Do maglocks need special exit hardware?
Yes. Maglocks require reliable ways to release for exit and are subject to specific code requirements.
More access control & cameras articles
- Access Control Systems Explained: Components, Credentials and Planning
- Business Security Cameras: Coverage, Recording and Working With Locks
- Card Access Systems for Doors: How Key Card Entry Works
- What Does Access Control Installation Cost? The Factors That Set the Price
- How to Choose an Access Control Installer
- Access Control for Homes: Keypads, Smart Locks and Gate Entry
- Building Access Control for Offices and Multi-Tenant Properties
- Key Fobs and Key Cards: Programming, Lost Fobs and Copies
- Access Control Systems in Marietta and Cobb County
- Security Camera Installation Cost: What Drives the Price
- How to Choose a Security Camera Installer