Commercial Doors & Hardware
Panic Bar Repair: Sticking Latches, Broken Bars and Replacement Parts
Common panic bar and exit device problems, from sticking latches to broken push pads, and when repair parts make sense versus replacement.
Updated November 18, 2026 · 3 min read · Arrowhead Lock & Safe
The most common problems
Exit devices on busy doors wear. The most frequent calls are latches that stick or don't retract, doors that don't latch when they close, push pads that feel loose or stay down, broken dogging, and outside trim that won't unlock. Vertical rod devices add problems at the top and bottom latches, especially bottom latches that drag on the floor or get bent.
Latch won't retract or catch
When pushing the bar doesn't release the door, the cause may be a worn internal part, a bent latch, or a strike that's binding against the latch because the door has sagged. When the door closes but doesn't latch, the strike may be out of alignment, the closer may not be bringing the door fully shut, or the latch spring may be weak. Each needs a different fix, which is why diagnosis comes before parts.
Vertical rod troubles
Vertical rod devices latch at the top and bottom of the door. Bottom latches take abuse from carts, mopping and floor debris; rods bend; and the timing between the bar and the latches drifts. Many facilities remove bottom rods entirely, which is called less-bottom-rod configuration, to reduce maintenance where code allows. Concealed vertical rods need careful adjustment inside the door.
Repair parts vs. replacing the device
Quality devices from Von Duprin, Detex and other commercial manufacturers have repair parts available: latch kits, springs, push pad components, dogging parts, strikes and trim. When the device body is sound, parts restore it for far less than a new device. Replacement makes sense when the device is a discontinued or low-quality brand, heavily damaged, or the wrong type for the door, such as a non-rated device on a fire door.
Outside trim and cylinders
Problems with outside pulls, levers and key cylinders are common too. Trim can loosen, levers can break after being forced, and cylinders can wear or need rekeying. Rekeying exit device cylinders to the building's master key system keeps key control consistent.
Prevent repeat failures
Fix the door, not just the device. Tighten or replace sagging hinges, adjust or replace the closer, and align the strike. Discourage staff from propping exit doors or kicking them open. And schedule periodic checks of exit hardware, since a failed exit device is a life-safety problem as well as a security one.
Emergency fixes vs. lasting repairs
When an exit device fails, the first priority is making sure people can still get out and that the building can be secured at night. Sometimes that means a temporary adjustment the same day, followed by parts ordered for a proper repair. A technician should explain which is which. Never chain, bar or padlock an exit door to make up for a broken device; that creates a serious life-safety hazard.
Keeping a few common parts for your building's devices on hand shortens repair time on the doors you depend on most.
Key control on exit devices
Exit device cylinders control dogging and outside trim, so they're part of your key system. Rekey them when keys go missing, and keep them on the same master key system as the rest of the building so management and staff carry fewer keys.
Exit device repair in Atlanta
Arrowhead repairs and stocks parts for commercial exit devices and services the doors they're mounted on for Atlanta buildings, schools and churches. Call 404-351-4331.
Frequently asked questions
Can a panic bar be repaired or does it need replacing?
Quality devices are usually repairable with manufacturer parts. Cheap or damaged devices are often better replaced.
Why does my exit door not latch?
Common causes are a misaligned strike, a door that doesn't fully close, or worn latch parts.
Is it okay to remove bottom rods?
In some cases, with approved conversion kits and code compliance. Ask before modifying fire-rated doors.
How often should exit devices be checked?
Regularly, especially on busy doors. Fire-rated door assemblies also have periodic inspection requirements.
More commercial doors & hardware articles
- Commercial Door Hardware Explained: Closers, Exit Devices, Strikes and Hinges
- Commercial Door Locks: Types, Grades and How to Choose
- Door Closer Repair: Common Problems and How They're Fixed
- Hydraulic Door Closers: How They Work and Why They Fail
- Door Closer Replacement: What Affects the Cost
- Storefront and Glass Door Closers: Overhead Concealed and Floor Closers
- Panic Bar Installation: Choosing and Installing Exit Devices