Serving Atlanta since 1973 |Now hiring technicians

404-351-4331
ARROWHEADLOCK & SAFE INC.

Commercial Doors & Hardware

Storefront and Glass Door Closers: Overhead Concealed and Floor Closers

How closers on aluminum storefront and glass doors work, common problems with overhead concealed and floor closers, and how they're repaired.

Updated November 18, 2026 · 3 min read · Arrowhead Lock & Safe

Closers you can't see

Most aluminum storefront and all-glass doors don't have the familiar closer arm at the top. Instead, the closer is concealed in the header above the door or set into the floor below it. The door pivots on top and bottom pins, and the closer controls its swing through the pivot. The clean look is the point, but it makes service a bit more involved.

Overhead concealed closers

Overhead concealed closers sit inside the aluminum header. An arm runs in a track on top of the door. Common problems include doors that drift open, slam, or stop closing fully, and arms that come out of their track after the door is forced. Adjustment valves are reached through the header. When the closer leaks, it's replaced by removing the door and sliding the old unit out of the header.

Floor closers

Floor closers sit in a metal box set into concrete beneath the door, common on all-glass doors and some storefronts. Water, cleaning chemicals and grit get into floor closers over time, causing corrosion and leaks. Symptoms include doors that won't stay centered, swing past closed, or wobble. Replacing a floor closer means removing the door, lifting out the closer and setting a new one level and aligned, sometimes after cleaning out or rebuilding the cement case.

Pivots and alignment

Storefront doors hang on pivots that wear. A worn top or bottom pivot lets the door sag, rub the frame or drag on the threshold, and then the closer struggles. Glass doors with patch fittings need those fittings tight and aligned. Fixing pivots and alignment is often part of any closer repair on these doors.

Locks, latches and exit devices

Storefront doors usually have narrow-stile locks or exit devices built for the thin aluminum frame. If the closer doesn't bring the door fully closed, the lock can't engage. That's a security gap many shop owners don't notice until the door is found unlocked in the morning. Checking that the door closes and latches every time is the most important test after any repair.

Keeping storefront doors working

Keep thresholds clean, especially around floor closers, avoid mopping water directly into the closer box, and don't let staff hold doors open with wedges. Have the door checked if it starts behaving differently, since early adjustment is much cheaper than replacing a damaged closer.

Offset and center-hung pivots

Storefront doors are either offset-hung, with the pivot set out from the door edge, or center-hung, with the pivot in the middle of the door's thickness. The closer must match. Replacing an offset closer with a center-hung model, or vice versa, won't work without other changes. Matching the hand of the door, the closer's spindle and the pivot set ensures the replacement fits and the door swings correctly.

Bringing the door's brand and a photo of the header or floor plate helps identify the right part quickly.

Storefront door service in Atlanta

Arrowhead repairs and replaces overhead concealed and floor closers, pivots and narrow-stile locks on Atlanta storefronts and glass doors. Call 404-351-4331.

Frequently asked questions

Why does my glass door swing past closed?

That's often a worn floor closer or pivot that has lost its center position.

Can a concealed closer be replaced without replacing the door?

Yes. The door is removed, the closer swapped, and the door rehung.

How do I know if a floor closer is leaking?

Oil around the floor plate, a door that swings freely, or one that won't hold center are common signs.

Can storefront doors have access control?

Yes. Electric strikes, electrified exit devices and other hardware are made for narrow-stile storefront doors.

Why won't my storefront door lock at night?

Usually the door isn't closing fully, so the lock bolt can't reach the strike. A closer or pivot adjustment typically fixes it.

Let's secure what matters

Talk with an Atlanta security professional.